Let's check out your computer without them being factors. I don't believe both are bad - but something is definitely wrong and I suspect it has to do with how the disks are managed or recognized or, at this point, even how they are formatted and if the formatting is proper, complete, and correct for either device.
But we'll get there as soon as we confirm your computer itself is OK. Do you know when this problem began? Be sure to check the box to show more than 5 days of restore points. If the first attempt fails, then try an earlier point or two. NOTE: You will have to re-install any software and updates you installed between now and the restore point, but you can use Windows Update for the updates.
The recovery disk works a bit different from the above procedures but if you follow the prompts from the System Restore menu option with the above information you should be able to restore with no problems. To do that, wait for the screen that tells you the F key to push to access the boot menu or boot setup.
Push it quickly. Make the changes, save your work, and exit. Put the CD in the drive and reboot. When prompted, push any key to boot from the CD. If that doesn't work, try to boot into safe mode repeatedly click the F8 key while booting and go to safe mode with networking — or do so from the command prompt on the disk. It will scan and try to fix some of your system files. Try to post any corrupted files here so we can see if they can be repaired with good copies from the installation disk unless there are too many.
It will want to schedule itself to run at the next restart. Answer yes and then reboot to run the program. It will scan and try to fix any corruption or bad sectors on your hard drive and mostly remove that as a potential cause. Look in the System section. You may be infected with malware. Try to run anti-malware programs in safe mode with networking if necessary. Before downloading pandasoft, uninstall whatever anti-virus program you are currently using because installing and running two at the same time can cause conflicts, freezes, and all sorts of problems.
Once you've uninstalled your current AV program, download, install, update, and scan using Pandasoft. I think you might be amazed at how much it finds that the other software missed. Once complete, uninstall pandasoft and re-install your current AV program unless you decide to switch which I did when I first tried it about 4 years ago. Reboot after completing all the scans. If the problem goes away then it's just a matter of tracking down the culprit causing the problem.
Follow the procedures in the article. Once found, delete, remove, deactivate, or uninstall it. Once done be sure to reset Vista back to normal status as explained in the procedures. If the problem occurs in clean mode then just restore the system to normal status and reboot - this solution is not going to work.
Boot into Safe mode with networking and see if the problem occurs there. Either result helps us narrow down the search for the cause. Check each device for a red x, yellow!
These identify devices with problems probably drivers, but also conflicts or something else. Click on each for further details and troubleshooting tips.
If you need to get drivers and you should do so for the USB drive and the SD reader at least and any you have time to do - they may help in ways beyond just resolving this problem , do so from the computer vendor or device manufacturer NOT from Microsoft Updates.
Now try plugging in the external USB drive to see if it is recognized. Reformat the drive as NTFS if that's still an issue I'm not quite sure if that was or wasn't accomplished.
Once done with that USB drive still attached, reboot and see if the problem occurs again. Hopefully not. Open MS Paint and paste the screenshot there and save the file to the desktop as a. Perhaps I'll be able to see the problem. To do this you have to also be able to boot normally. Although this will not affect your data, settings, or programs, you should still backup your data before starting just to be on the safe side.
You may have a lot of updates to re-install including any service packs you had to remove. This should give you enough access to the system if you can't get in any other way to backup your important data. Once done, you can do a clean install either using the genuine Windows Vista Installation Disk or the Recovery Disk or the Recovery Partition whatever process is dictated by your computer manufacturer — you may need to contact them for the procedure and perhaps to get recovery disks.
Then you will need to re-install all your programs, reset all your preferences, reconfigure your network and email settings, restore your backed up data, run Windows Update with possibly nearly updates pending, Hopefully one of these procedures will resolve or at least identify the cause of your problem.
Was this reply helpful? Yes No. Add a comment. Active Oldest Votes. Jody Klymak Jody Klymak 3, 2 2 gold badges 11 11 silver badges 24 24 bronze badges. Can you please explain me, what do you mean with the actual error message?
Error messages in python include a stack trace. You have also not indicated what environment you are running in. Unfortunately the rest of us cannot reproduce your problem. If it is really matplotlib causing the problem you should be able to reproduce without Pillow by plotting random arrays.
Just to be clear "Fail to allocate bitmap" is not a matplotlib error message, so we need more information about your environement. What backend are you using? If your goal is just to save plots, set it to "agg" and avoid opening any windows. My environment is Anaconda on Windows Python 3. I loop this line and I get the error message "Fail to allocate bitmap" after times into the loop.
I also try to print the stack trace but unfortunately I have no any extra information printed. Sign up or log in Sign up using Google. Sign up using Facebook. Sign up using Email and Password. Post as a guest Name.
Email Required, but never shown. The Overflow Blog. Podcast Helping communities build their own LTE networks. Podcast Making Agile work for data science. Featured on Meta.
0コメント